Basic Info.
Model NO.
2hss86h JMC driver +8nm motor
Application
Hybrid Servo Motor
Number of Stator
Two-Phase
Excitation Mode
HB-Hybrid
Function
Control, Driving
Operate Mode
Hybrid Servo Motor
Certification
ISO9001, CCC
Brand
Jmc Hybrid Servo Motor
Specification
hybrid servo motor
Product Description
HYCNC 8 nm 12N China factory OEM available 1.8 degree NEMA 34 stepper motor stepping motor controller driver kit with CE
1.When installing the drives, ensure that the equipment is well ventilated. When multiple drives are used in parallel in the cabinet, ensure that the distance between each other is not less than 5cm.2.In order to ensure the safety of use, please make sure to connect the protective ground terminal of the drive well to the protective ground of the equipment!
EnvironmentCooling | Natural Cooling or Forced Convection |
Environment | Storage Space | Avoid dust, oil frost and corrosive gases |
Ambient Temperature | -20°C - +80°C |
Humidity | <80%RH |
Vibration | 5.9m/s² Max |
Storage Temp | |
Weight | |
Electrical SpecificationsParameters | | | | |
Supply voltage | | | | |
Output Current (Peak) | | | | |
Logic Input Current | | | | |
Pulse input frequency | | | | |
Low Level Time | | | | |
FeaturesFull closed loop control
Motor with standard 1000 line encoder
It save energy and achieve nearly 100% output torque .
Micro step setting range is 2-256
High speed response , High speed
Optical isolation fault alarm output interface ALM
Current loop bandwidth: (-3dB) 2KHz (typical value)
Speed loop bandwidth: 500Hz (typical value)
Position loop bandwidth: 200Hz (typical value)
RS232 serial communication available to download or change the parameters
Optical isolation fault alarm output interface ALM
Over current, I2T, over voltage, under voltage,temperature, speeding, over-differential protection
Alarm clear input ENA
The power-on time of the drive depends on the size of the external AC voltage, and the typical power-on time is 2 seconds under AC60V.
| | |
LED does not light up | Wrong power connection | Check the power connection |
Low power supply voltage | Increase power supply voltage |
The motor does not rotate and there is no holding torque | The motor connection is wrong | Correct the motor connection |
Offline enable RESET signal is valid | Invalidate RESET |
The motor does not rotate, but there is a holding torque | No pulse signal input | Adjust pulse width and signal level |
Motor rotation direction is wrong | Wrong connection of power line phase sequence | Swap any two connected lines |
Wrong direction signal input | Change direction setting |
Motor torque is too small | Phase current setting is too small | Correctly set the phase current |
Acceleration too fast | Decrease acceleration value |
Motor stalled | Troubleshoot mechanical problems |
Driver and motor do not match | Change to a suitable drive |
Precautions1. Since the driver has no overheating protection, please install a heat sink when the temperature of the driver exceeds 70 degrees.2. Over current (excessive current or low voltage) fault indicator AL ARM light J is on, please check the motor wiring and other short-circuit faults or whether the voltage is too low, if the motor wiring and other short-circuit faults, need to be re-powered after troubleshooting restore.
3. The green indicator light PWR is on when the power is turned on.
4. When the above protection functions are activated, the motor shaft loses its self-locking force and the power indicator light turns red. If you want to resume normal operation, you need to confirm that the above faults are eliminated, and then power on again, the power indicator light turns green, the motor shaft is locked, and the drive returns to normal.
model | Body L | Flange | Shaft diameter D | keyway | Shaft length LL |
86J1880EC-1000 | | 73/60 optional | | Platform 1.0*25 | |
86J1895EC-1000 | | 73/60 optional | | Platform 1.0*25 | |
86J18118EC-1000 | | 73/60 optional | | Keyway 5.0*25 | |
86J18156EC-1000 | | 73/60 optional | | Keyway 5.0*25 | |
Packing & Delivery
Company Profile
Address:
Jinan, Shandong, China
Business Type:
Manufacturer/Factory
Business Range:
Tools & Hardware
Management System Certification:
ISO 9001
Company Introduction:
Jinan Hongyang CNC Machinery Co., Ltd, founded in 2008 is a global famous supplier for CNC router accessories. Selling: Spindle, inverters, stepper motors, hybrid servos motors, drives, guide rails, sliders, gear box, racks, water chillers, reducers, CNC controller, transformers, power supply, vacuum cleaner, dust hood, tool sensor, limit sensor, lubricant oil pump, linear atc with cutters, round atc with cutters, cylinder, cable chain towline, engraving cutters, control cabinet, vacuum suction table and so on. Welcome your inquiry.